Inon Snoot Set for S-2000
Rated 3.5/5 based on 11 customer reviews

Inon Snoot Set for S-2000

Available: In Stock
Wishlist
$215.00

Various combination for different beam coverage

Various combination of packaged parts provides 6 different beam coverage to suit to a subject and intended effect.

[Pattern 1]
Rubber Hood 52
(when collapsed)
 
[coverage]
approx. 105°(horizontal)
approx. 95°(vertical)
 
To block extra diffused light eliminating backscatter

[Pattern 2]
Rubber Hood 52
(when extended)
 
[coverage]
approx. 65°(horizontal)
approx. 60°(vertical)

[Pattern 3]
Rubber Hood 52
(when extended)
+Snoot Tube 26
+W 40°filter LE
 
[coverage]
approx. 26°(horizontal)
approx. 24°(vertical)

[Pattern 4]
Rubber Hood 52
(when extended)
+Snoot Tube 26
 
 
[coverage]
approx. 31°(horizontal)
approx. 19°(vertical)

[Pattern 5]
Rubber Hood 52
(when extended)
+ Snoot Tube 10
+W 40° filter LE
 
[coverage]
approx. 16°(horizontal)
approx. 12°(vertical)

[Pattern 6]
Rubber Hood 52
(when extended)
+Snoot Tube 10
 
 
[coverage]
approx. 22°(horizontal)
approx. 9°(vertical)

*Beam coverage is actual measured data by INON INC and could have variant depending on test condition.

*Always conduct test shots to familiar with the product characteristic before you take an important shot. When using the S-2000 in S-TTL Auto mode for spotlight effect of this product, center spot metering mode on a camera is recommended since average metering mode or multi pattern metering mode could wash out the center of an image. In case S-TTL Auto mode does not provide appropriate exposure, use Manual mode.
 
*Make sure to cool down the "S-2000" according to instruction manual / [Compatible battery, operational limitation on flashing] leaflet provided with the S-2000, to prevent overheating / degradation of light emitting part / inner components. The light emitting part could have discoloration or burn when excessive repeated flashes are made. Should you observe any irregularity mentioned above, stop using the strobe immediately.
 
*"Slave D Holder Unit 3" of the "Optical D Slave Cable III Type L" is not compatible with this product.
 
*When you entry with this product being attached on a strobe, make sure to evacuate remaining air inside of the Rubber Hood before you get underwater.
 
*Always extend the "Rubber Hood 52" when using the "Snoot Tube 10" or "Snoot Tube 26" together to prevent possible damage on light emitting part and/or inner circuit of the S-2000 etc. since generated heat could stay close to the light emitting part.

 

Various combination for different beam coverage

Various combination of packaged parts provides 6 different beam coverage to suit to a subject and intended effect.

[Pattern 1]
Rubber Hood 52
(when collapsed)
 
[coverage]
approx. 105°(horizontal)
approx. 95°(vertical)
 
To block extra diffused light eliminating backscatter

[Pattern 2]
Rubber Hood 52
(when extended)
 
[coverage]
approx. 65°(horizontal)
approx. 60°(vertical)

[Pattern 3]
Rubber Hood 52
(when extended)
+Snoot Tube 26
+W 40°filter LE
 
[coverage]
approx. 26°(horizontal)
approx. 24°(vertical)

[Pattern 4]
Rubber Hood 52
(when extended)
+Snoot Tube 26
 
 
[coverage]
approx. 31°(horizontal)
approx. 19°(vertical)

[Pattern 5]
Rubber Hood 52
(when extended)
+ Snoot Tube 10
+W 40° filter LE
 
[coverage]
approx. 16°(horizontal)
approx. 12°(vertical)

[Pattern 6]
Rubber Hood 52
(when extended)
+Snoot Tube 10
 
 
[coverage]
approx. 22°(horizontal)
approx. 9°(vertical)

*Beam coverage is actual measured data by INON INC and could have variant depending on test condition.

*Always conduct test shots to familiar with the product characteristic before you take an important shot. When using the S-2000 in S-TTL Auto mode for spotlight effect of this product, center spot metering mode on a camera is recommended since average metering mode or multi pattern metering mode could wash out the center of an image. In case S-TTL Auto mode does not provide appropriate exposure, use Manual mode.
 
*Make sure to cool down the "S-2000" according to instruction manual / [Compatible battery, operational limitation on flashing] leaflet provided with the S-2000, to prevent overheating / degradation of light emitting part / inner components. The light emitting part could have discoloration or burn when excessive repeated flashes are made. Should you observe any irregularity mentioned above, stop using the strobe immediately.
 
*"Slave D Holder Unit 3" of the "Optical D Slave Cable III Type L" is not compatible with this product.
 
*When you entry with this product being attached on a strobe, make sure to evacuate remaining air inside of the Rubber Hood before you get underwater.
 
*Always extend the "Rubber Hood 52" when using the "Snoot Tube 10" or "Snoot Tube 26" together to prevent possible damage on light emitting part and/or inner circuit of the S-2000 etc. since generated heat could stay close to the light emitting part.

 

SHIPPING

Following are the terms and conditions that constitute our Shipping Policy. Domestic Shipping Policy Shipment processing time All orders are processed within 1-2 business days. Orders are not shipped or delivered on weekends or holidays. If we are experiencing a high volume of orders, shipments may be delayed by a few days. Please allow additional days in transit for delivery. If there will be a significant delay in shipment of your order, we will contact you via email or telephone. Shipping rates & delivery estimates Shipping charges for your order will be calculated and displayed at checkout.

RETURNS POLICY

Once we receive your item, we will inspect it and notify you that we have received your returned item. We will immediately notify you on the status of your refund after inspecting the item. If your return is approved, we will initiate a refund to your credit card (or original method of payment). You will receive the credit within a certain amount of days, depending on your card issuer's policies. You will be responsible for paying for your own shipping costs for returning your item. Shipping costs are non refundable. If you receive a refund, the cost of return shipping will be deducted from your refund. Contact Us If you have any questions on how to return your item to us, contact us

We will not entertain returns as a result of change of heart or other matters besides defects.